vy jste tam nahrali posledni firmware ? Jeslti jo, je v nem problem, siae ma dve banky na firmware, takze v te druhe je ten predchozi a jde to prepnout.
Po restartu to umi jet na defaultni zachrane ip adresy:
strana 136:
https://ekatalog.ispalliance.cz/upload/ ... 3e_ED6.pdf
9.4 CONNECTION PROCEDURE
Connection between PC and ALFOplus can only occur if the IP address of the PC and the radio belong to
the same subnet and it can be made directly or through a switch on the LAN2 connector.
Using Subnetwork Craft Terminal (SCT) (you know IP address):
1. press button Options, a window will open; select card Connection
2. select Connect using local area network (see Fig.81)
3. press OK and Connect
4. type the equipment IP address stored previously (Factory Default are 172.20.254.14/16 ODU L and
172.20.255.15/16 ODU H)
- Default User: SYSTEM
- Default Password: SIAEMICR
5. after connection it’s possible to modify IP address, etc.....
Using WebLCT console (WLC) (you know IP address):
1. add the IP address of radio in the LAN address book (see Fig.85)
2. press double click over the IP address to open the browser.
Rescue connection using SCT (you don’t know IP address)
1. Assign a static IP address (see Fig.82) to PC (172.20.253.14/255.255.0.0)
ALFOplus rescue IP address: 172.20.253.13
ALFOplus rescue subnetwork mask: 255.255.0.0
2. Connect your PC directly to ALFOplus with a LAN cable
3. By SCT, connect using Local Area Network, press connect button, type equipment user/password
and press RESCUE button (see Fig.83)
4. Follow the instructions of rescue login (see Fig.84)
5. In “Rescue Connection” mode it is possible to set or recover the values for management access.
Rescue connection using WLC (you don’t know IP address)
1. Assign a static IP address (see Fig.82) to PC (172.20.253.14/255.255.0.0).
ALFOplus rescue IP address: 172.20.253.13
ALFOplus rescue Subnetwork Mask: 255.255.0.0
2. Connect your PC directly to ALFOplus with a LAN cable
3. By WLC, press the arrow down near the button connect and press “Rescue connection” (see Fig.85)
4. Type equipment user/password and follow the instructions of rescue login (see Fig.86)
5. In “Rescue connection” mode it is possible to set or recover the values for management access.
MN.00273.E - 006 137
Rescue connection using “Command Prompt” (you don’t know IP address)
1. Assign a static IP address (see Fig.82) to PC (172.20.253.14/255.255.0.0)
ALFOplus rescue IP address: 172.20.253.13
AFOplus rescue Subnetwork Mask: 255.255.0.0
2. Connect your PC directly to ALFOplus with a LAN cable
3. By command prompt, type “ping 172.20.253.13 -t” and press Enter.
4. Restart hardware ALFOplus
5. Wait till the ping reply, open Internet Explorer, type in the URL: 172.20.253.13 and press F5 until
the login menu appears
6. In rescue connection mode it is possible to set or recover the values for management access.
Emergency connection (you don’t know IP address)
1. Connection between PC and ALFOplus with serial console cable (F03594) in auxiliary connector
2. using Hyperterminal - serial COM at 115200bps, 8bits, none parity, 1 stop bit, no flow control and
press “Enter” button to access in the login
3. after login will be shown the radio IP address
4. type “Config” if you want to change the boot parameters (IP address, etc...)
