Verze 7.20.1

iTomB

What's new in 7.20.1 (2025-Oct-10 11:49):

*) bgp - added output.network-blackhole setting;
*) bgp - do not auto-generate blackhole routes by default (introduced in v7.20);
*) bgp - fixed inactive flag in GUI after instance disable/enable;
*) console - fixed ".id" printing when using "group-by" (introduced in v7.20);
*) console - fixed relative path printing (introduced in v7.20);
*) ike1 - fixed an issue where policies could be released too early before re-acquisition;
*) ipsec - improved driver stability;
*) ipv6,ra - fixed prefix unlinking from interface on configuration change and stop deprecating prefixes when the validity lifetime expires;
*) lte - fixed issue with firmware update for FG621-EA modem;
*) ppp - added support for KNOT BG77 modem firmware upgrade to version BG77LAR02A04_A0.301.A0.301;
*) qos-hw - always use qos-hw-offloading=yes for CRS812 device;
*) quickset - fixed issue where routes set by QuickSet did not appear in export;
*) route - improved stability;
*) routerboard - fixed non-running interfaces for CRS310-8G+2S+IN after booting to SwOS ("/system routerboard upgrade" required) (introduced in v7.20);
*) sfp - improved interface link speed configuration for CRS812;
*) snmp - fixed SNMP trap messages being corrupted when sent to multiple targets;
*) switch - fixed "failure: cpu flow control not supported" (introduced in v7.20);
*) webfig - fixed form closing with saving when pressing Enter key (introduced in v7.20);
*) webfig - fixed interface settings and graphs (introduced in v7.20);
*) webfig - improved container form loading performance when router has a lot of files;
*) winbox - fixed WinBox 3 application failure when opening IPv6/Firewall/Connection entry (introduced in v7.20);
*) www - improved stability (CVE-2025-10948);

pgb

Hlavně že se chytli za nos s těmi bgp blackhole routami. To jsou mi taky nápady...

iTomB

pgb Spis aby opravili CASPsMAN V3 pro qcom-ac ...
V navodu bridge, se pise:

PVID - The Port VLAN ID is used for access ports to tag all ingress traffic with a specific VLAN ID. A dynamic entry is added in the bridge VLAN table for every PVID used, the port is automatically added as an untagged port.

Problem je, ze pro AX to da do tagged a funguje to (asi maji nejake upravy v ovladacich). Pro qcom-ac to daji taky do tagged a nefunguje to. Musi se to rucne pridavat, delat si rucne virtualni WiFi, pouzit slaves-static=yes.
Proste kravina. Kdyby k tomu jeste misto slaves-static (nevi nekdo, zda se to nepouziva jeste pro neco jineho?) dali moznost pridani seznam interface, ktere by se k dane VLANe pridali jako TAGGED? Tim by bylo mozne plne VLANy definovat pomoci CAPsMANa (pridani tagged by byl uplink port - mozno i vice portu - backup cesta atd.).

maxdevaine

Beru zpět, vše zatím vypadá ok.

misif

Upgradoval jsem cca stovku zařízení v 60GHz LHGG, nRAY, Cube 60ad a začalo se mi náhodně stávat, na to množství jak obden jeden případ, že spojem netečou data, přestože je spojení navázané (je jedno, jestli je klient bridge nebo NAT). Restart libovolné strany dočasně pomůže. Downgrade klienta na 7.19.3 je řešení.
Máte někdo podobný problém?

Grey

Zdravím... nějaký posun odpojování/připojování klientů ?? co verze testing 7.21beta3(5) ?????? už opraveno tam? 😃